Honda Motorcycles - FireBlades.org banner

Status
Not open for further replies.
1 - 20 of 27 Posts

·
Registered
Joined
·
203 Posts
Discussion Starter #1
Hey Everyone, I just had an accident on the bike, and unfortunately I am selling off the parts. Good thing I had a cage on it, which saved the bike. I will be putting everything up for sale and post pictures later on. Please email if you are interested in certain parts. I am located in Southern California, Garden Grove. Local is always best. The only thing I can tell you off that bat that was not saved was the right front rotor, the left sato rearset ( you can get the replacement parts from their site), the exhaust broke from the mid pipe, exhaust itself was brushed with the saddle bag. and both right and left fairings have 1 1/2 in holes on the bottom, and the tail has a line crack next to the rear signal. O yea, the right fork got the little nub knocked off, its the one that holds the front fender in place. Good Luck


---------------------------

Hey guys,

I just finished my 2003 cbr954rr project, and going to move on to my next project. I have put a lot of time and effort into this bike, beautiful bike, I know someone will have a great time with it. The bike has around 11K miles, never been dropped or in an accident.

Dunlops SportMax Front Tire (New)
Dunloas SportMax Back Tire (New)
Carrozzeria Wheels (New)
Front and Rear Galfer Rotors
Front and Rear Galfer Brake Pads (New)
Brembo Front Brake Calipers
Brembo Rear Caliper Relocator Kits (New)
Brenbo Rear Caliper (New)
Galfer SS Red Brake Lines (front/back) (New)
Gilles Chain Adjuster
Pro-Tek Triple Clamp (New)
Gilles Lifters
Gilles Rear Axle Safety Nut (New)
Ohlins Rear Shock
Race Tech Fork Internals
G2 Ergonomics Throttle (New)
Motion Pro Throttle Cables (New)
HID Lights
LED Block Off Mirrors
CRG Bar End Mirrors
CRG Clutch Lever with Perch (New)
Brembo 19 RCS Brake Master
Rizoma Front Brake Reservoir (New)
Brembo Brake Switch (New)
Gilles Clipon (New)
Techmount (New)
DynoJet LCD (New)
DynoJet Fuel Module (New)
DynoJet Ignition Module (New)
DynoJet PowerCommander
DynoJet Quick Shifter (New)
SATO Foot Levers
Frame Sliders
Competition Werkes Fender Eliminator
Corbin Seat
Targa Rear Seat Eliminator
RK Chain 520 (New)
Vortex Front Sprocket (New)
SuperSproket Rear Sprocket (New)
Scorpion Alarm
Sportvue HUD
Greggs Custom Flush LED Mounts
Custom Rear Fender LED
Billet Inner Led Mounts
Billet Spools
Micron Full Exhaust (New)
Intergrated Rear Light
Smoked Headlight
Decal Kit
Scotts Steering Dampner
Custom Tank Protector
Under Fender LED lights
Red Windshield Bolts (New)
K&N Airfilter (New)
Nitrous Setup
NGK Spark Plugs (New)
COX Radiator Guard
SpeedoHealer
Factory Pro Shift Kit
Barnett Clutch Kit
Freestyle Ingenuity Cage
LED System (Remote Control System)
Samco Radiator Hose (New)
Clear Puig windshield
Factory Pro Velocity Stacks (New)
Engine Cage
Brembo RCS Remote Adjuster
O2 Eliminator Kit (New)



and last but not least the pictures.



http://i880.photobucket.com/albums/a...t/DSC02458.jpg

http://i880.photobucket.com/albums/a...t/DSC02459.jpg


http://i880.photobucket.com/albums/a...t/DSC02460.jpg

http://i880.photobucket.com/albums/a...t/DSC02461.jpg

http://i880.photobucket.com/albums/a...t/DSC02462.jpg

http://i880.photobucket.com/albums/a...t/DSC02463.jpg

http://i880.photobucket.com/albums/a...t/DSC02464.jpg

http://i880.photobucket.com/albums/a...t/DSC02465.jpg

http://i880.photobucket.com/albums/a...t/DSC02466.jpg

http://i880.photobucket.com/albums/a...t/DSC02467.jpg

http://i880.photobucket.com/albums/a...t/DSC02468.jpg

http://i880.photobucket.com/albums/a...t/DSC02469.jpg

http://i880.photobucket.com/albums/a...t/DSC02470.jpg

http://i880.photobucket.com/albums/a...t/DSC02473.jpg

http://i880.photobucket.com/albums/a...t/DSC02474.jpg

http://i880.photobucket.com/albums/a...t/DSC02475.jpg

http://i880.photobucket.com/albums/a...t/DSC02476.jpg

http://i880.photobucket.com/albums/a...t/DSC02477.jpg


:-D Enjoy, and good luck, I will even throw in a Chatterbox bluetooth, not the tiny one, but the big one :-D
 

·
Registered
Joined
·
7,455 Posts

·
Registered
Joined
·
26 Posts
Het, how much are you wanting to get for that underslung brembo rear?
And also, how much for the galfer fronts and the galfer rear rotors? It might be easier to reach me by a text at 573-823-8573. Thanks bud!
 

·
Registered
Joined
·
1,375 Posts
Are you guys surfing through the individual forums, or do you click on active topics?
Anyway, if you want to see some sickass parts, the links are working on his original thread from 2-1/2 years ago. I caught it in the Active topics, as he resurrected it today and I wanted to know about his forks for my buddy that just bought a 954.

http://www.fireblades.org/forums/motorcycles-for-sale/89941-2003-cbr954rr-raced-out.html
active topics. I thought it looked familiar, but I've been losing my mind lately, so I thought I'd just point it out...
 

·
Registered
Joined
·
7,455 Posts
active topics. I thought it looked familiar, but I've been losing my mind lately, so I thought I'd just point it out...
Hey Brandon, how's it going?
I'm glad you did point out this thread since dicedreams started this and restarted his old one too. I suppose he did that so it would be a current thread, not an oldy-moldy. I dunno.
Sure didn't mean to criticize.
 

·
Registered
Joined
·
21 Posts
Hey Everyone, I just had an accident on the bike, and unfortunately I am selling off the parts. Good thing I had a cage on it, which saved the bike. I will be putting everything up for sale and post pictures later on. Please email if you are interested in certain parts. I am located in Southern California, Garden Grove. Local is always best. The only thing I can tell you off that bat that was not saved was the right front rotor, the left sato rearset ( you can get the replacement parts from their site), the exhaust broke from the mid pipe, exhaust itself was brushed with the saddle bag. and both right and left fairings have 1 1/2 in holes on the bottom, and the tail has a line crack next to the rear signal. O yea, the right fork got the little nub knocked off, its the one that holds the front fender in place. Good Luck


---------------------------

Hey guys,

I just finished my 2003 cbr954rr project, and going to move on to my next project. I have put a lot of time and effort into this bike, beautiful bike, I know someone will have a great time with it. The bike has around 11K miles, never been dropped or in an accident.

Dunlops SportMax Front Tire (New)
Dunloas SportMax Back Tire (New)
Carrozzeria Wheels (New)
Front and Rear Galfer Rotors
Front and Rear Galfer Brake Pads (New)
Brembo Front Brake Calipers
Brembo Rear Caliper Relocator Kits (New)
Brenbo Rear Caliper (New)
Galfer SS Red Brake Lines (front/back) (New)
Gilles Chain Adjuster
Pro-Tek Triple Clamp (New)
Gilles Lifters
Gilles Rear Axle Safety Nut (New)
Ohlins Rear Shock
Race Tech Fork Internals
G2 Ergonomics Throttle (New)
Motion Pro Throttle Cables (New)
HID Lights
LED Block Off Mirrors
CRG Bar End Mirrors
CRG Clutch Lever with Perch (New)
Brembo 19 RCS Brake Master
Rizoma Front Brake Reservoir (New)
Brembo Brake Switch (New)
Gilles Clipon (New)
Techmount (New)
DynoJet LCD (New)
DynoJet Fuel Module (New)
DynoJet Ignition Module (New)
DynoJet PowerCommander
DynoJet Quick Shifter (New)
SATO Foot Levers
Frame Sliders
Competition Werkes Fender Eliminator
Corbin Seat
Targa Rear Seat Eliminator
RK Chain 520 (New)
Vortex Front Sprocket (New)
SuperSproket Rear Sprocket (New)
Scorpion Alarm
Sportvue HUD
Greggs Custom Flush LED Mounts
Custom Rear Fender LED
Billet Inner Led Mounts
Billet Spools
Micron Full Exhaust (New)
Intergrated Rear Light
Smoked Headlight
Decal Kit
Scotts Steering Dampner
Custom Tank Protector
Under Fender LED lights
Red Windshield Bolts (New)
K&N Airfilter (New)
Nitrous Setup
NGK Spark Plugs (New)
COX Radiator Guard
SpeedoHealer
Factory Pro Shift Kit
Barnett Clutch Kit
Freestyle Ingenuity Cage
LED System (Remote Control System)
Samco Radiator Hose (New)
Clear Puig windshield
Factory Pro Velocity Stacks (New)
Engine Cage
Brembo RCS Remote Adjuster
O2 Eliminator Kit (New)



and last but not least the pictures.



http://i880.photobucket.com/albums/a...t/DSC02458.jpg

http://i880.photobucket.com/albums/a...t/DSC02459.jpg


http://i880.photobucket.com/albums/a...t/DSC02460.jpg

http://i880.photobucket.com/albums/a...t/DSC02461.jpg

http://i880.photobucket.com/albums/a...t/DSC02462.jpg

http://i880.photobucket.com/albums/a...t/DSC02463.jpg

http://i880.photobucket.com/albums/a...t/DSC02464.jpg

http://i880.photobucket.com/albums/a...t/DSC02465.jpg

http://i880.photobucket.com/albums/a...t/DSC02466.jpg

http://i880.photobucket.com/albums/a...t/DSC02467.jpg

http://i880.photobucket.com/albums/a...t/DSC02468.jpg

http://i880.photobucket.com/albums/a...t/DSC02469.jpg

http://i880.photobucket.com/albums/a...t/DSC02470.jpg

http://i880.photobucket.com/albums/a...t/DSC02473.jpg

http://i880.photobucket.com/albums/a...t/DSC02474.jpg

http://i880.photobucket.com/albums/a...t/DSC02475.jpg

http://i880.photobucket.com/albums/a...t/DSC02476.jpg

http://i880.photobucket.com/albums/a...t/DSC02477.jpg


:-D Enjoy, and good luck, I will even throw in a Chatterbox bluetooth, not the tiny one, but the big one :-D
I'm interested in your Suspension parts and break lines. How much for all. The Ohlin rear shocks expecially. Targa seat, sato foot lever and volocity stacks.
 

·
Super Moderator
Joined
·
14,706 Posts
Hey Everyone, I just had an accident on the bike, and unfortunately I am selling off the parts. Good thing I had a cage on it, which saved the bike. I will be putting everything up for sale and post pictures later on. Please email if you are interested in certain parts. I am located in Southern California, Garden Grove. Local is always best. The only thing I can tell you off that bat that was not saved was the right front rotor, the left sato rearset ( you can get the replacement parts from their site), the exhaust broke from the mid pipe, exhaust itself was brushed with the saddle bag. and both right and left fairings have 1 1/2 in holes on the bottom, and the tail has a line crack next to the rear signal. O yea, the right fork got the little nub knocked off, its the one that holds the front fender in place. Good Luck


---------------------------

Hey guys,

I just finished my 2003 cbr954rr project, and going to move on to my next project. I have put a lot of time and effort into this bike, beautiful bike, I know someone will have a great time with it. The bike has around 11K miles, never been dropped or in an accident.

Dunlops SportMax Front Tire (New)
Dunloas SportMax Back Tire (New)
Carrozzeria Wheels (New)
Front and Rear Galfer Rotors
Front and Rear Galfer Brake Pads (New)
Brembo Front Brake Calipers
Brembo Rear Caliper Relocator Kits (New)
Brenbo Rear Caliper (New)
Galfer SS Red Brake Lines (front/back) (New)
Gilles Chain Adjuster
Pro-Tek Triple Clamp (New)
Gilles Lifters
Gilles Rear Axle Safety Nut (New)
Ohlins Rear Shock
Race Tech Fork Internals
G2 Ergonomics Throttle (New)
Motion Pro Throttle Cables (New)
HID Lights
LED Block Off Mirrors
CRG Bar End Mirrors
CRG Clutch Lever with Perch (New)
Brembo 19 RCS Brake Master
Rizoma Front Brake Reservoir (New)
Brembo Brake Switch (New)
Gilles Clipon (New)
Techmount (New)
DynoJet LCD (New)
DynoJet Fuel Module (New)
DynoJet Ignition Module (New)
DynoJet PowerCommander
DynoJet Quick Shifter (New)
SATO Foot Levers
Frame Sliders
Competition Werkes Fender Eliminator
Corbin Seat
Targa Rear Seat Eliminator
RK Chain 520 (New)
Vortex Front Sprocket (New)
SuperSproket Rear Sprocket (New)
Scorpion Alarm
Sportvue HUD
Greggs Custom Flush LED Mounts
Custom Rear Fender LED
Billet Inner Led Mounts
Billet Spools
Micron Full Exhaust (New)
Intergrated Rear Light
Smoked Headlight
Decal Kit
Scotts Steering Dampner
Custom Tank Protector
Under Fender LED lights
Red Windshield Bolts (New)
K&N Airfilter (New)
Nitrous Setup
NGK Spark Plugs (New)
COX Radiator Guard
SpeedoHealer
Factory Pro Shift Kit
Barnett Clutch Kit
Freestyle Ingenuity Cage
LED System (Remote Control System)
Samco Radiator Hose (New)
Clear Puig windshield
Factory Pro Velocity Stacks (New)
Engine Cage
Brembo RCS Remote Adjuster
O2 Eliminator Kit (New)



and last but not least the pictures.





:-D Enjoy, and good luck, I will even throw in a Chatterbox bluetooth, not the tiny one, but the big one :-D
AS PER SITE RULES ALL ITEMS FOR SALE MUST HAVE A PRICE. PLEASE CONFORM OR THE APPROPRIATE ACTION WILL BE TAKEN! Thankyou.
 

·
Registered
Joined
·
1,375 Posts
Hey Brandon, how's it going?
I'm glad you did point out this thread since dicedreams started this and restarted his old one too. I suppose he did that so it would be a current thread, not an oldy-moldy. I dunno.
Sure didn't mean to criticize.
lol, nah man, no offense taken at all. Just a lot of bullshit with work that's been weighing on my mind. Then I can't ride because it's raining and still 100* out the past couple weeks. Found me a HOT little blond a few days ago to help distract me though, worked like a charm so far lol
 

·
Registered
Joined
·
1,375 Posts
AS PER SITE RULES ALL ITEMS FOR SALE MUST HAVE A PRICE. PLEASE CONFORM OR THE APPROPRIATE ACTION WILL BE TAKEN! Thankyou.
he said he's asking $6500 in the original thread (which, considering all the mods, is a hell of a deal too. Can't believe it's been around this long)
 
1 - 20 of 27 Posts
Status
Not open for further replies.
Top